Television Fundementals
In this report on television I will discuss television signals, the
components
the make up a television, and how a television produces the
picture and sound
for the final output. The sound carrier is at the upper end
of the spectrum.
Frequency modulation is used to impress the sound on the
carrier. The maximum
frequency deviation is twenty-five kilohertz,
considerably less than the
deviation permitted by confessional FM stereo. As
a result, a TV sound signal
occupies less bandwidth in the spectrum than a
standard FM broadcast station.
Stereo sound is available in TV, and the
multiplexing method used to transmit
two channels of sound information is
virtually identical to that used in stereo
transmission for FM broadcasting.
The picture information is transmitted on a
separate carrier located 4.5 MHz
lower in frequency than the sound carrier. The
video signal derived from a
camera is used to amplitude modulate the picture
carrier. Different methods
of modulation are used for both sound and picture
information so that there
is less interference between the picture and sound
signals. The full upper
sidebands of the picture information are transmitted,
but only a portion of
the lower sidebands is suppressed to conserve spectrum
space. The color
information in a picture is transmitted by way of frequency
division
multiplexing techniques. Two color signals derived from the camera are
used
to modulate a subcarrier that, in turn, modulates the picture carrier
along
with the main voice information. The color subcarriers
use
double-sideband-suppressed carrier AM. The video signal can contain
frequency
components up to 4.2 MHz. Therefore, if both sidebands were
transmitted
simultaneously, the picture signal would occupy 8.4 MHz. The
vestigal sideband
transmission reduces this excessive bandwidth. Because a TV
signal occupies so
much bandwidth, it must be transmitted in a very high
frequency portion of the
spectrum. TV signals are assigned to frequencies in
the VHF and UHF range.
United States TV stations use the frequencies
between 54 and 806 MHz. This
portion of the spectrum is divided into
sixty-eight 6MHz channels that are
assigned frequencies. Channels 2 through 7
occupy the frequency range from 54 to
88 MHz. Additional TV channels
occupy the space between 470 and 806 MHz. The
video signal is most often
generated by a TV camera, a very sophisticated
electronic device that
incorporates lenses and light-sensitive tranducers to
convert the scene or
object to be viewed into an electrical signal that can be
used to modulate a
carrier. To do this, the scene to be transmitted is collected
and focused by
a lens upon a light-sensitive imaging device. Both vacume tube
and
semiconductor devices are used for converting the light information in
the
scene into an electrical signal. The scene is divided into smaller
segments that
can be transmitted serially over a period of time. It is the
job of the camera
to subdivide the scene in an orderly manner so that an
acceptable signal is
developed. This process is called scanning. Scanning is
a technique that divides
a rectangular scene up into individual lines. The
standard TV scene dimensions
have an aspect ratio of 4:3; that is, the scene
width is four units for every 3
units of height. To create a picture, the
scene is subdivided into many fine
horizontal lines called scan lines. Each
line represents a very narrow portion
of light variations in the scene. The
greater the number of scan lines, the
higher the resolution and the greater
the detail that can be observed. United
States TV standards call for the
scene to be divided into a maximum of 525
horizontal lines. The task of the
TV camera is to convert the scene into an
electrical signal. The camera
accomplishes this by transmitting a voltage of 1
volt for black and 0 volts
for white. The scene is divided into 15 scan lines
numbered 0 through 14. The
scene is focused on the light-sensitive area of a
vidicon tube or CCD imaging
device that scans the scene one line at time,
transmitting the light
variations along the lines as voltage levels. Where the
white background is
being scanned a 0 volt signal occurs. When a black picture
element is
encountered a 1 volt level is transmitted. The electrical signals
derived
from each scan line are refereed to as the video signal. They are
transmitted
serially one after the other until the entire scene has been sent.
Since
the scene contains colors, there are different levels of light along
each
scan line. This information is transmitted as different shades of gray
between
black and white. Shades of gray are represented by some voltage level
between 0-
and 1-V extremes represented by white and black. The resulting
signal is known
as the brightness, or luminance and is usually designated by
the letter Y.
Resolution in a video system is measured in terms of the
number of lines defined
within the bounds of the picture. For example, the
horizontal resolution is
given as the maximum number of alternating black and
white vertical lines that
can be distinguished. Assume closely spaced
vertical black and white lines of
the same width, when such lines are scanned
they will they will be converted
into a square wave. One cycle or period, of
this wave is the time for 1 black
and 1 white line. The video signal
described so far contains the video or
luminance information, which is a
black and white version of the scene. To add
the color detail, this is done
by dividing the light in each scan line into
three separate signals, each
representing one of the three basic colors, red,
green or blue. In the same
way, light in any scene can be divided into its three
basic color components
by passing the light through red, green and blue filters.
This is done in
a color TV camera, which is really three cameras in one. The
lens focuses the
scene on three separate light-sensitive devices such as a
videcon tube or a
CCD imaging device by way of a series of mirrors and beam
splitters. The red
light in the scene passes through the red filter, the green
passes through
the green filter and the blue passes through the blue filter. The
result is
the generation of three simultaneous signals during the scanning
process by
the light-sensitive imaging devices. The R, G and B signals also
contain the
basic brightness or luminance information. If the color signals are
mixed in
the correct proportion, the result is the standard B&W video or
luminance
Y signal. The Y signal is generated by scaling each color signal with
a
tapped voltage divider and adding the signals together. The Y signal is
made
up of 30 percent red, 59 percent green and 11 percent blue. The
resulting Y
signal is what a B&W TV set will see. The color signals must
also be
transmitted along with the luminance information in the same
bandwidth allotted
to the TV signal. This is done by a frequency division
multiplexing technique.
Instead of all three color signals being
transmitted they are combined into
color signals referred to as the I and Q
signals. I is made up of 60 percent
red, 28 percent green and -32 percent
blue. Q is made up of 21 percent red, -52
percent green and 31 percent blue.
The I and Q signals are referred to as the
chrominance signals. To transmit
them they are phase-encoded. These I and Q
signals are fed to balance
modulators along with 3.58 MHz subcarrier signals
that are 90 degrees out of
phase. The output of each balanced modulator is a
double-sideband supressed
carrier AM signal. The resulting two signals are added
to the Y signal to
create the composite video signal. The combined signal
modulates the picture
carrier. The resulting signal is the NTSC composite video
signal. This signal
and its sidebands are within the 6MHz TV signal bandwidth.
The I and Q
color signals are also called the R - Y and the B - Y signals as
the
combination of the three color signals produces the effect of subtracting
Y from
the R or B signals. The phase of these signals with respect to the
original 3.58
MHz subcarrier signal determines the color to be seen. In
many TV sets an extra
phase shift of 57 degrees is inserted to ensure that
maximum color detail is
seen. There is still 57 degrees between the I and Q
signals but their position
is moved 57 degrees. The reason for this extra
phase shift is that the eye is
more sensitive to the color orange. If the I
signal is adjusted to the orange
phase position better detail will be seen.
Because of the frequency of the
subcarrier, the sidebands produced during
amplitude modulation occur in clusters
that are interleaved between the other
sidebands produced by the video
modulation. The 3.58 MHz subcarrier is
supressed by the balanced modulators and
therefore is not transmitted. Only
the filtered upper and lower sidebands of the
color signals are transmitted.
To demodulate these double-sideband AM signals,
the carrier must be
reinserted at the receiver. A 3.58 MHz oscillator in the
receiver generates
the subcarrier for the balanced modulator-demodulator
circuits. For the color
signals to be accurately recovered, the subcarrier at
the receiver must have
a phase related to the subcarrier at the transmitter. To
ensure the proper
conditions at the receiver, a sample of the 3.58 MHz
subcarrier signal
developed at the transmitter is added to the composite video
signal. This is
done by gating 8 to 12 cycles of the 3.58 MHz subcarrier and
adding it to the
horizontal sync and blanking pulse. The receiver uses this
signal to
phase-synchronize the internally generated subcarrier before it is
used in
the demodulation process. In a TV transmitter, the sweep and sync
circuits
that creates the scanning signals for the vidicons or CCDs as well
as
generate the sync pulses that are transmitted along with the video and
color
signals. The sync signals, luminance Y and the color signals are added
to form
the final video signal that is used to modulate the carrier.
Low-level AM is
used. The final AM signal is amplified by very high power
linear amplifiers and
sent to the antenna via a diplexer. At the same time
the voice or sound signals
frequency modulate a carrier that is amplified by
class C amplifiers and fed to
the same antenna by way of the diplexer. The
resulting VHF or UHF signal travels
by line-of-sight propagation to the
antenna and receiver. The process involved
in receiving a TV signal and
recovering it to present the picture and sound
outputs in a high-quality
manner is complex. Over the course of the past 50
years since its invention,
the TV set has evolved from a large vacume tube unit
into a smaller and more
reliable solid-state unit made with mostly ICs. The
signal from the antenna
or the cable is connected to the tuner. The tuner is
used to select which TV
channel is to be viewed and to convert the picture and
sound carriers plus
their modulation to an intermediate frequency (IF). As in
most
superheterodyne receivers, the local oscillator frequency is set higher
than
the incoming signal by the IF value. The local oscillators are
phase-locked
loop frequency synthesizers set to frequencies that will convert
the TV signals
to the IF. Tuning of the local oscillator is typically done
digitally. The PLL
synthesizer is tuned by setting the feedback frequency
division ratio. In a TV
set this is changed by a microprocessor which is part
of the master controlled
system. The interstage LC-resonant circuits in the
tuner are controlled by
varactor diodes. By varying the DC bias on the
varactors, their capacitance is
changed, thereby changing the resonant
frequency of the tuned circuits. The bias
control signals also come from the
control microprocessor. Most TV sets are also
tuned by IR remote control. The
standard TV receiver IFs are 41.25 MHz for the
sound and 45.75 MHz for the
picture. The synthesizer local oscillator is set to
113 MHz. The tuner
produces an output that is the difference between the
incoming signal and the
local oscillator frequencies. The IF signals are then
sent to the video IF
amplifiers. Selectivity is usually obtained with a surface
acoustic wave
filter. This fixed tuned filter is designed to provide the exact
selectivity
required to pass both of the IF signals with the correct response to
match
the vestigal sideband signal transmitted. A pattern of interdigital
filters
on the surface convert the IF signals into acoustic waves that travel
across
the filter surface. By controlling the shape, sizes and spacing of
the
interdigital filters, the response can be tailored to any
application.
Interdigital filters at the output convert the acoustic
waves into electrical
signals at the IF. The IF signals are next amplified by
IC amplifiers. The video
signal is then recovered by an AM demodulator. In
older TV sets a simple diode
detector was used for video detection. In modern
TV sets a synchronous modulator
type of synchronous demodulator is used. The
output of the video detector is the
Y signal or the composite color
signal, which are amplified by the video
amplifiers. The Y signal is used to
create an AGC voltage output for controlling
the gain of the IF amplifiers
and mixers. The composite color signal is taken
from the video amplifier
output by a filter and fed to color-balanced
demodulator circuits. The color
burst signal is also picked up by a gating
circuit and sent to a phase
detector whose output is used to synchronize an
oscillator that produces a
3.58 MHz subcarrier signal of the correct frequency
and phase. The output of
this oscillator is fed to two balanced modulators that
recover the I and Q
signals. The carriers fed to the two balanced modulators are
90 degrees
out of phase. The Q and I signals are combined in matrix with the Y
signal,
and out comes the R, G and B color signals. These are amplified and sent
to
the picture tube, which produces the picture. To recover the sound part
of
the TV signal a separate sound IF and detector section are used. The sound
and
picture IF signals are fed to a sound detector circuit. This is a
nonlinear
circuit that heterodynes the two IFs and generates the sum and the
difference of
the frequencies. The result is a difference signal that
contains both the AM
picture and the FM sound modulation. This is the IF
sound signal. It is passed
to the sound IF amplifiers which also perform a
clipping-limiting function which
removes the AM, leaving only the FM sound.
The audio is recovered with a
quadrature detector or differential peak
detector. The audio is amplified by one
or more audio stages and sent to the
speaker. If stereo is used the appropriate
demultiplexing is done by an IC,
and the left and right channel audio signals
are amplified. A major part of
the TV receiver is dedicated to the sweep and
synchronizing functions that
are unique to TV receivers. To display the picture
on a picture tube, special
sweep circuits are needed to generate the voltages
and currents to operate
the picture tube, the sync circuits are needed to keep
the sweep in step with
the transmitted signal. The sweep and sync operations
begin in the video
amplifier. The demodulated video includes the vertical and
horizontal
blanking and sync pulses. The sync pulses are stipped off the video
signal
with a sync seperator circuit and fed to the sweep circuits. The
horizontal
sync pulses are used to synchronize a horizontal oscillator to 15,734
Hz.
This oscillator drives a horizontal output stage that developes a sawtooth
of
current that drives magnetic deflection coils in the picture tube yoke
that
sweep the electron beams in the picture tube. The horizontal output
stage is
also part of a switching power supply. The horizontal output
transistor drives a
step-up-step-down transformer called the flyback. The
15.734 KHz pulses
developed are stepped up, rectified, and filtered to
develope the 30 to 35 KV
high direct current required to operate the picture
tube. Step-down windings on
the flyback produce the lower voltage pulses that
are rectified and filtered
into low voltages that are used as power supplies
for most of the circuits in
the receiver. The sync pulses are also fed to an
IC that takes the horizontal
sync pulses during the vertical blanking
interval and integrates them into a 60
Hz sync pulse that is used to
synchronixe a vertical sweep oscillator. The
output from this oscillator is a
sawtooth sweep voltage at the field rate of 60
Hz. This output is
amplified and converted into a linear sweep current that
drives the magnetic
coils in the picture tube yoke. These coils produce vertical
deflection of
the electron beams in the picture tube. In most modern TV sets,
the
horizontal and vertical oscillators are replaced by digital sync
circuits.
The horizontal sync pulses from the sync seperator are normally
used to phase
-lock a 31.468 KHz voltage controlled oscillator that runs at
two times the
normal horizontal rate of 15.734 KHz. Dividing this by two in a
flip-flop gives
the horizontal pulses that are amplified and shaped in the
horizontal output
stage to drive the deflection coils on the picture tube. A
digital frequency
divider divides the 31.468 KHz signal by 525 to get a 59.94
Hz signal for
vertical sync. This signal is shaped into a current sawtooth
and amplified by
the vertical output stage which drives the deflection coils
on the picture tube.
A picture tube is a vactume tube called a
cathode-ray tube (CRT).Both monochrome
and color picture tubes are available.
The tube is housed in a bell shaped glass
enclosure. A filament heats a
cathode that emits electrons. The negatively
charged electrons are attracted
and accelerated by positive-bias voltages on the
elements in an electron gun
assembly. The electron gun also focuses the
electrons into a very narrow
beam. A control grid that is made negative with
respect to the cathode
controls the intensity of the electron beam and the
brightness of the spot it
makes. The beam is accelerated forward by a very high
voltage applied to an
internal metallic coating called aquadag. The face or the
front of the
picture tube is coated internally with a phosphor that glows and
produces
white light when it is struck by the electron beam. Around the neck of
the
picture tube is a structure of magnetic coils called the deflection
yoke.
The horizontal and vertical current linear sawtooth waves generated
by the sweep
and synchronizing circuits are applied to the yoke coils, which
produce magnetic
fields inside the tube that influence the position of the
electron beam. When
electrons flow, a magnetic field is produced around the
conductor through which
current flows. The magnetic field that occurs around
the electron beam is moved
or deflected by the magnetic field produced by the
deflection coils in the yoke.
Thus the electron beam is sweep across the
face of the picture n tube in the
interlaced manner. As the beam is being
sweep across the face of the tube to
trace out the scene, the intensity of
the electron beam is varied by the
luminance, or Y, signal, which is applied
to the cathode or in some cases to the
control grid. By varying the grid
voltage, the beam can be made stronger or
weaker, thereby varying the
intensity of the light spot produced by the beam
when it strikes the
phosphor. Any shade of gray, from white to black can be
reproduced this way.
To produce color, the inside of the picture tube is coated
with many tiny
red, green and blue phosphor dots arranged in groups of three
called triads.
Some tubes use a pattern of red, green and blue stripes. These
dots or
stripes are energived by three seperate cathodes and electron guns
driven by
the red, green and blue color signals. A metallic plate with holes for
each
dot triad called a shadow mask is between the guns and the phosphor dots
to
ensure that the correct beam strikes the correct color dot. By varying
the
intensity of the color beams the dot triads can be made to produce any
color.
The dots are small enough so that the eye cannot see them
individually at a
distance. What the eye sees is a color picture swept out on
the face of the
tube. This report was intended to cover the fundamentals of
television. I
covered TV signals, signal bandwidth, the process of generating
a video signal,
TV receiver fundamentals, TV tuner fundamentals, voice IF
and demodulation,
sound IF and demodulation, synchronizing circuits and the
picture tube. I hope
that you have found this report on television to be
informative and enjoyable.